Elecrow Crowpanel Adv 4.3/5.0/7.0 TFT
Also known as Crowpanel Adv 4.3/5.0/7.0 TFT, CROWPANEL, elecrow-adv1-43-50-70-tft
A free replacement firmware exists.
Meshtastic LoRa mesh firmware listing. Upstream hardware model 97 (CROWPANEL), target elecrow-adv1-43-50-70-tft, architecture esp32-s3. Listed as actively supported. Upstream support-level code: 1. Board revisions, attached radio modules and frequency variants must match the upstream instructions. This is not an OpenDeviceDB hardware test.
Get started
One known way to put open firmware or software on this device, easiest first. Each one links to the project's own instructions.
- Back up your data and settings (and the stock firmware, when the guide says how).
- Check the exact model, hardware revision and firmware version against the guide: a close model may not work.
- Charge the battery or use a stable power supply; do not unplug during the install.
Install Meshtastic over USB (bootloader unlock)
Install: mediumNeeds a cable or the command line · Meshtastic
- Device opened
- No
- Firmware
- Select the exact elecrow-adv1-43-50-70-tft board target and hardware revision. Upstream marks this device as requiring DFU; follow its model-specific bootloader instructions.
Read the hardware and installation documentation for the complete board/module combination and existing bootloader before installing.
No install report yet. · Report how it went
OpenDeviceDB links to each project's own instructions and tools; nothing is flashed from this site. Flashing is at your own risk and may void the warranty.
- ID
- elecrow/crowpanel-adv-4-3-5-0-7-0-tft
- Category
- radio
- Vendor support
- Unknown
- Updated
- 2026-11-16
Being worked on
No live claim. If you start working on this device, claim it so nobody duplicates your work.
Interfaces
No interface documented yet.
Projects
| Project | Kind | Origin | License | Freedom |
|---|---|---|---|---|
| Meshtastic (elecrow-adv1-43-50-70-tft; active) | firmware | community | GPL-3.0 | Still non-free: not stated · Cloud: noneUpstream hardware model 97 (CROWPANEL), target elecrow-adv1-43-50-70-tft, architecture esp32-s3. Listed as actively supported. Upstream support-level code: 1. Board revisions, attached radio modules and frequency variants must match the upstream instructions. This is not an OpenDeviceDB hardware test. ESP32 wireless stacks may require vendor blobs; this index does not audit every component's freedom. |
What "still non-free" and "cloud" mean
What stays proprietary or depends on the vendor's cloud once the project is in use, from the project's own documentation.
- vendor blobs
- proprietary files extracted from the stock firmware
- stock firmware
- the stock firmware stays on the device; the project only talks to it
- modem
- cellular modem firmware
- GPU
- graphics driver or firmware
- Wi-Fi
- Wi-Fi driver or firmware
- Bluetooth
- Bluetooth firmware
- camera
- camera driver or image processing
- sensors
- sensor hub or sensor drivers
- bootloader
- boot firmware
- other
- another proprietary part
- Cloud: none
- works fully locally
- Cloud: only at setup
- a vendor account is needed once, e.g. to obtain a local key
- Cloud: optional
- cloud features exist but are not needed
- Cloud: required
- does not work without the vendor's cloud
- Cloud: unknown
- not known
Verification
Not verified. A "verified on hardware" badge requires a replayable test (hardware-replay) run on a real device with a stated firmware version.
Provenance
- Meshtastic mesh radios (GPL-3.0, fetched 2026-11-16) · about this source
AI assistance not stated.
Status and claims as of the build date (2026-11-16). Data licensed CC BY-SA 4.0; imported data keeps its upstream license.

